How to time a workout that only gives you rep counts
“3 rounds: 15 squats, 10 push ups, 20 mountain climbers.” Plenty of workouts are written like this, and an interval timer cannot run it as is. Here is how to turn rep counts into seconds that match how fast you actually move.
By Magic Park Labs, the studio that builds Zestimer · · 6 min read
Written by the people who build Zestimer, so when a post describes the app, it is describing our own work. We are not doctors or physiotherapists. This is general information, not medical advice: if something hurts, or you are working around an injury, ask someone qualified.
Why bother converting at all
Counting reps is fine when you are fresh. By round three you are counting, breathing and remembering what comes next all at once, and the count is the first thing to go. Was that eleven or thirteen? A timer takes the counting off your hands: you move well until it tells you to stop.
The catch is that a time is not the same instruction as a rep count. Fifteen squats is a fixed amount of work done at whatever speed. Forty seconds of squats is a fixed amount of time, and the work depends on your pace. The goal of converting is to pick a time that gives you roughly the work the author meant, at a pace where your form holds.
Measure your own pace once
Generic numbers for seconds per rep are a guess about somebody else. Your own number takes about two minutes to find:
- Do five reps of each move at the pace you would use in round two, not round one. Controlled, full range, no rushing.
- Time the five with your phone’s stopwatch and divide by five. That is your seconds per rep for that move.
- Multiply by the reps the workout asks for, then round up to the nearest five seconds. Round up, not down: the last reps of a set are always slower than the first.
Slow, controlled moves like squats and glute bridges usually take longer per rep than people expect. Fast alternating moves like mountain climbers go the other way. That difference is exactly why one number for every move does not work.
The adjustments that catch people out
- “Each side” means double. Twenty mountain climbers each side is forty steps. For a one sided move like a single leg glute bridge, give each side its own interval rather than one long one, so the switch is called rather than guessed.
- Holds are already time. A “30 second plank” needs no conversion. Copy it across as written.
- Sets are rounds. “3 × 12” is a 12 rep interval run three times. Write it as a circuit with rounds, not as three separate moves.
- Getting into position takes time. If a move starts on the floor after a standing one, the first few seconds of its interval go to getting down. Either add five seconds to that move or lengthen the rest before it.
- Rest is a separate number. A post that says nothing about rest is not telling you to skip it. Start with rest about half as long as the work, then see how the work to rest ratio changes the session.
A worked example
Here is the post from the top of this article, converted for someone who measured 2.5 seconds per squat, 3 seconds per push up and 1 second per mountain climber step:
| As written | Your pace | Interval |
|---|---|---|
| 15 squats | 15 × 2.5 s = 37.5 s | 40 s |
| 10 push ups | 10 × 3 s = 30 s | 35 s (floor transition) |
| 20 mountain climbers each side | 40 × 1 s = 40 s | 40 s |
| Rest between moves | not stated | 20 s |
| 3 rounds | 3 rounds |
That is a circuit of three moves, 40, 35 and 40 seconds, with 20 seconds of rest, run three times: just under nine minutes. You can run exactly that in the free web interval timer, which counts rounds for you, if you are happy with one work length for every move.
When the timer and the count disagree
Sometimes the timer runs out at twelve squats instead of fifteen. That is fine. A timed interval is a cap, not a target, and finishing twelve good reps is a better session than rushing fifteen. If it happens every round, your pace number was optimistic: add five seconds. If you are finishing early and standing around, take five off.
After one session the numbers stop being a conversion and become your own routine. That is the point where it is worth saving.
How Zestimer handles it
When you share a post into Zestimer that only lists reps, the importer proposes a time for each move so the workout can run. Treat those numbers as a first draft, the same way you would treat a pace you had not measured yet. Every interval and every rest is editable before you press start, so the two minutes of measuring above are still the quickest way to get times that fit you. The YouTube and TikTok pages explain the import itself.
Full Body HIIT10:00 · 10 movesQuestions
- How many seconds is one rep?
- It depends on the move and on you, which is why measuring is better than a rule. Time five controlled reps, divide by five, and you have a number for that move at your pace.
- How do I convert 3 sets of 12 reps into a timed workout?
- Find your seconds per rep, multiply by 12, round up to the nearest five seconds, and run that interval for 3 rounds with rest between them.
- What if I do not finish the reps before the timer ends?
- Stop when the timer does. A timed interval is a cap. If it happens every round, add five seconds to that move next time.
- Should rest be timed too?
- Yes. Rest is what decides how hard the session feels. If the workout does not say, start with rest about half the length of the work and adjust after one run.